5-Pack 433MHz Garage Door Remote Control – Auto Sliding/Gate Opener & Closer, Electric Cloning Replacement for Rolling Driveway Gates – Compatible with Most Fixed Code Openers

Product description

5-Pack 433MHz Garage Door Remote Control for various gate and garage door systems

Compatible with most fixed-code 433MHz gate systems

PLEASE NOTES: Be sure to check the applicable chip type before purchasing!!!Not fit for C-O-Z Sliding GateCompatible with most fixed-code 433MHz gate systemsNot compatible with rolling code systems or encrypted protocols.This is a fixed-code remote; it does not support remote-to-remote learning or auto-cloning.

Our product can copy the IC model: PT2260, PT2262, PT2264, PT1527, PT527, PT1587, PT1827, HS2260, HS2262, HS2264, HS2240, HS1527, HS527, HS1587, HS1827, RT2260, RT2262, RT2264, RT2240, RT1527, SC527, SC1587, SC1827, SC2260, SC2262, SC2264, SC2240, SC1527, SC527, SC1587, SC1827, EV2262, EV2264, EV2240, EV1527

Troubleshooting Guide for Wire-less Remote Control IssuesProduct Name: Garage Door Opener Remote ControlFunction: Automatic sliding door opener, garage door opener replacement, electric rolling driveway gate opener.If you encounter issues with your product not working, follow these detailed troubleshooting steps:1. Check Frequency Compatibility Ensure your remote is set to 433 MHz. Our remote controls operate exclusively on this frequency; other frequencies will not work.2. Verify Original Remote Functionality Make sure that your original remote control functions properly before attempting to clone or replace it. This helps rule out any existing issues with the system.3. Special Rolling Codes Issue If you experience a situation where the remote works only once and then stops functioning (“They will not work with the board.”), it indicates the use of special rolling codes. These codes change each time, making consistent functionality impossible. Avoid using our remotes with systems employing such codes.4. Ensure Correct Chip Support Verify that your system uses one of the supported chips: 2260 (all manufacturers), 2262 (all manufacturers), PT2264, 5326 (all manufacturers), SC5262, HT600, HT680, HT6207, HT6010, HT6012, HT6014, SMC918 series, 527 (all manufacturers), 1527 (all manufacturers), 2240 (all manufacturers), HCS101, HCS200\HCS201 (some codes), HCS300\HCS301 (some codes), and some microcontrollers.5. Correct Reset Procedure To reset the remote, press and hold both “A” and “B” buttons until the LED blinks three times. Release “B” but keep holding “A,” then tap “B” three more times. The LED will flash rapidly, indicating all data has been cleared. Post-reset, pressing any button should not light up the LED.6. Proper Cloning Method Hold your original remote in one hand and the new remote in the other, placing them as close together as possible. Press the corresponding buttons on both remotes; the LED should flash quickly three times, signaling successful cloning. For weaker signal remotes, place them back-to-back during cloning. Avoid interference sources and re-clone after resetting if necessary.7. System Compatibility Check Confirm compatibility with your specific opener model. For example, if you have a CO-Z opener, ensure it supports the same frequency and chip type as our remote.8. Battery Installation Double-check that the batteries are correctly installed and fully charged. Incorrect battery installation can prevent the remote from operating correctly.9. Environmental Interference Be aware of potential environmental interferences such as nearby electronic devices or structures that might block or interfere with the signal. Moving to an open area away from obstructions can improve functionality.10. Seek Professional Help If after following all steps your remote still does not function, consider reaching out to cust-omer support or consulting with a professional technician. There may be underlying issues with either the remote or the receiver that require expert attention.By systematically addressing each point, you can identify and resolve most common issues encountered with wireless remote controls.

Wide Compatibility: Open any 433.92 MHz sliding gate from a distance with this handy remote control. PLEASE NOTES: The market includes various types of gate systems using different encoding technologies (e.g., Fixed Code), this product is only Compatible with most fixed-code 433MHz gate systems – NOT compatible with rolling code or encrypted systems (e.g., Som-mer, LiftM-aster Secu-ralift, Ni-ce, etc.)”
Copy the IC Model: PT2260, PT2262, PT2264, PT1527, PT527, PT1587, PT1827, HS2260, HS2262, HS2264, HS2240, HS1527, HS527, HS1587, HS1827, RT2260, RT2262, RT2264, RT2240, RT1527, SC527, SC1587, SC1827, SC2260, SC2262, SC2264, SC2240, SC1527, SC527, SC1587, SC1827, EV2262, EV2264, EV2240, EV1527. PLEASE NOTES: “This is a fixed-code remote; it does not support remote-to-remote learning or auto-cloning.” Be sure to check the applicable chip type before purchasing!!!
Easy to Clear Old Codes: Simultaneously long press the A and B key on the universal gate remote until the LED indicator keeps flashing, then you can let go, you could press any keys to test, if the LED indicator blinks instead of keeping flashing, which means codes have been cleared.“Compatible with most fixed-code 433MHz gate systems”“Not compatible with rolling code systems or encrypted protocols.”
Methods to Duplicate: Place the universal remote for gate opener and old remote control side by side; Press the A button (Do not move); Then press the corresponding button of the old remote control to copy; The LED indicators will flash about 3 times, then you can let go; Reset the BCD key in the same way as the A key.
4 Keys to Control: There are 4 keys on the remote controls for gates to open, close, bell and call the police. Convenient and practical, which are suitable for rolling shutter door, rolling gate, telescopic door, garage door, road gate, etc.
Important: Our product is designed for standard coding systems and is not compatible with special rolling code (dynamic code) systems. Rolling code technology generates a unique, constantly changing code with each use, meaning the signal cannot be reused. As a result, our device will not function properly after the first use in such systems. We strongly advise to verify your system type before purchasing. Your satisfaction is our priority — we are committed to providing accurate information to ensure you select the right product for your needs

Product summary

shift
+
opt
+
D